FAS2050 System Installation and Setup
Copyright © 2009 NetApp, Inc. All rights reserved.
Unpack and verify contents
Before you begin
1 2
If you have not already done so, gather the required information and confirm your site
requirements, as described in the Site Requirements Guide at http://now.netapp.com/.
Your system comes with an accessory kit that includes the following components:
- This installation poster - Power cables
- Software license flyer - DB-9 to RJ-45 console adapters
- System Manager CD-ROM - Rail kit (for two-post and four-post racks)
- Grounding kit
Install in rack
3
Caution: Only use the NetApp
®
rail kit to install your system. Using a different rail kit can cause injury to you or damage to your system.
Four-post rack
Cable the system
4
Connect power
Connect the installed PCI card, as needed.
5
Cable controllers
RJ-45 to DB-9 adapter to console port (required)
1
e0be0a0a 0b
8
Fibre
Channel
Ethernet
Console
Remote
Management
Port
Port labels
Network cables to e0a and e0b ports
3
e0be0a0a 0b
8
Console cable to adapter
2
e0be0a0a 0b
8
Boot the system and proceed with setup
5
- Turn on the power to your system. It takes the LEDs on your system power supplies a few seconds to illuminate.
- Windows® environments with DHCP: Install System Manager from the CD-ROM and run it on a Windows client system to discover, configure, and manage your system. Connect your
Windows client system through the management LAN.
- All other configurations: Use the console interface and proceed through the setup questions. See the Data ONTAP Software Setup Guide at http://now.netapp.com/.
Cable disk shelves
These are a few common configurations. For additional options, see Supported Configurations for
FAS2000-series Systems at http://now.netapp.com.
or
Active/Active NAS or ISCSI:
1 Fibre Channel Disk Shelf Stack (Multipath)
Active/Active SAN: 4 FCP
Connections 1 Fibre Channel Disk Shelf Stack (Multipath)
U
SPU
S
P
DS14
IN
OUT
IN
OUT
USPUSP
DS14
IN
OUT
IN OUT
USPUSP
FAS2050
a0ea0
1b 1a
e0b0b
1b 1a
CM-B
b0ea0ea0 0b
10101
10101
1
Controller to shelf
USPUSP
DS14
INOUT
IN
OUT
USP
U
SP
DS14
IN
OUT
IN OUT
U
S
P
U
S
P
FAS2050
a0ea0
1b 1a
e0b0b
1b 1a
CM-B
b0e
a
0ea
0
0b
10101
10101
3
Shelf to controller
US
PU
SP
DS14
INOUT
IN
OUT
USPUS
P
DS14
INOUT
IN OUT
USPUSP
FAS2050
a0ea
0
1b 1a
e0b0b
1b 1a
CM-B
b0
e
a
0ea
0
0b
10101
10101
2
Shelf to shelf
USPUSP
DS14
INOUT
IN OUT
U
S
P
U
SP
DS14
IN
OUT
IN OUT
USPUSP
FAS2050
a
0
e
a0
1b 1a
e0b
0b
1b 1a
CM-B
b0
e
a
0
ea
0
0b
10101
10101
1
Controller to switches
U
S
P
USP
DS14
IN
OUT
IN OUT
U
SP
U
S
P
DS14
INOUT
IN OUT
U
S
P
U
S
P
FAS2050
a0
e
a0
1b 1a
e0b
0b
1b 1a
CM-B
b0ea
0
ea0
0b
10101
10101
3
Shelf to controller
U
S
P
U
SP
DS14
INOUT
IN OUT
US
PUS
P
DS14
INOUT
IN OUT
U
S
P
U
S
P
FAS2050
a
0e
a
0
1b 1a
e0b
0b
1b 1a
CM-B
b
0
e
a
0ea0
0b
10101
10101
2
Controller to shelves
Note: Refer to the rail kit installation flyer included with the rail kit for the two-post procedure.
210-03951+C0
Note: You do not need to
ground your system.
Network cable to Remote Management port
4
6
e0be0a
8
0a 0b
8
(4x)
4U
3U
3U
FRONT SIDE
Clip nut (4x)
(2x)
(2x)
Front rail
Clip nut
tool
Note: The disk shelf IDs for the
disk shelves should be set in the
range 1 to 6. Leave the FAS2050
disk shelf ID at the preset value of 00.
1
Shelf ID
switch
Note: Remove handles after the
system is supported by the shelf.
Setting the Disk Shelf IDs
(2x)
Trim-17” x 22”
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels