VMware VCENTER SERVER 4.0 - GETTING STARTED UPDATE 1 Guide d'installation Page 38
- Page / 72
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installation Guide
38 VMware, Inc.
If the Secondary server is physical, go to Step 2
1 Before powering on the Secondary (cloned) image, right-click the server image and select Edit Settings.
a Select the Principal (Public) virtual network adapter and clear the Connected and Connect at power
on check boxes.
b Repeat the process on the VMware Channel virtual network adapter.
c Power on the Secondary (previously cloned) server image.
d On the Secondary server, open Network Connections, right-click the VMware Channel network
connection, and select Properties. Select Internet Protocol (TCP/IP) and click Properties.
e Configure the appropriate VMware Channel IP address and Subnet Mask. Click Advanced
fClick the WINS tab, select Disable NetBIOS over TCP/IP and Click OK three times to close the
dialogs.
g Right-click the Principal (Public) network connection and select Properties. Select Internet Protocol
(TCP/IP) and click Properties. Configure the Principal (Public) IP address (same as the Primary
server), Subnet Mask, and Default Gateway.
hClick OK three times to close the dialogs.
i Right-click the Secondary (cloned) server image and select Edit Settings.
j Select the VMware Channel virtual network adapter and select the Connected and Connect at power
on check boxes. IP communications with the Secondary server go through the VMware Channel.
2 To install the vCenter Server Heartbeat on the Secondary server, download vCenter Server Heartbeat to
the Secondary server (either physical or virtual) to a suitable location. Execute the self-extracting file to
start the installation process.
The Setup Introduction dialog appears. Review the information and click
OK.
3The WinZip Self-Extractor dialog appears. Click Setup to continue.
4The Setup Type page appears. As with the installation on the Primary server, select Install VMware
vCenter Server Heartbeat and click Next.
5 Select the identity of the server on the Physical Hardware Identity page. Select Secondary as the server
identity and click Next.
6 Identify the location of the folder containing the backup file from the Primary server. Manually type the
location path in the text box. Click Next.
N
OTE Do not connect the Principal (Public) virtual network adapter at this time to prevent an IP
address conflict on the network.
N
OTE If you click Exit after Setup has started, you are prompted to save your settings. When you run the
self-extracting file again later, you will be asked if you want to use the previously saved configuration.
N
OTE The left pane of each page in the setup wizard provides information about the setup process.
N
OTE If .Net 2.0 SP2 is not currently installed on the server, vCenter Server Heartbeat Setup installs this
required component, taking some additional time during the installation process.
N
OTE For Windows Server 2003 installations you can alternatively click Browse and locate the folder. On
Windows Server 2008 installations, you must use the UNC path.
- Installation Guide 1
- 2 VMware, Inc 2
- Contents 3
- Glossary 67 4
- About This Book 5
- Abbreviations Used in Figures 6
- Getting Started 7
- 8 VMware, Inc 8
- Introduction 9
- Server Protection 10
- Network Protection 11
- Application Protection 11
- Performance Protection 11
- Communications 12
- Managed Switchover 13
- Automatic Switchover 14
- Automatic Failover 14
- Managed Failover 15
- 16 VMware, Inc 16
- Installation 17
- 18 VMware, Inc 18
- Implementation 19
- Common Requirements 20
- Server Architecture Options 21
- Cloning Technology Options 22
- Application Component Options 22
- VMware, Inc. 23 23
- Network Options 24
- Primary Server 25
- Secondary Server 25
- WAN Requirements 25
- Antivirus Recommendations 26
- Deployment Options Summary 27
- 28 VMware, Inc 28
- Overview 29
- Installation Process 29
- VMware VirtualCenter Server 30
- vCenter Inventory Service 30
- VMware, Inc. 31 31
- 32 VMware, Inc 32
- VMware, Inc. 33 33
- 34 VMware, Inc 34
- VMware, Inc. 35 35
- 36 VMware, Inc 36
- 38 VMware, Inc 38
- VMware, Inc. 39 39
- 40 VMware, Inc 40
- VMware, Inc. 41 41
- 42 VMware, Inc 42
- VMware, Inc. 43 43
- Renaming the Servers 44
- Resulting IP Configuration 45
- Add a vCenter Server Group 46
- Add a New Connection 46
- VMware, Inc. 47 47
- 48 VMware, Inc 48
- Installation of Client Tools 49
- 50 VMware, Inc 50
- VMware, Inc. 51 51
- 52 VMware, Inc 52
- Server Heartbeat 53
- Parameter File Elements 54
- VMware, Inc. 55 55
- 56 VMware, Inc 56
- VMware, Inc. 57 57
- 58 VMware, Inc 58
- VMware, Inc. 59 59
- VMware, Inc. 61 61
- 62 VMware, Inc 62
- Windows XP 32 bit SP3 63
- Windows XP 64 bit SP2 63
- 64 VMware, Inc 64
- VMware, Inc. 65 65
- 66 VMware, Inc 66
- Glossary 67
- D Data Replication 68
- F Failover 68
- G Graceful (Clean) Shutdown 68
- VMware, Inc. 69 69
- Q Quality of Service (QoS) 70
- S Security Identifier (SID) 70
- VMware, Inc. 71 71
- V VMware Channel 72
Produits connexes et manuels pour Serveurs VMware VCENTER SERVER 4.0 - GETTING STARTED UPDATE 1
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels