VMware VCENTER SERVER 4.0 - GETTING STARTED UPDATE 1 Guide d'installation télécharger pdf (Page 10)

QuickStart Guide

10 VMware, Inc.

9 Double-click the self-extracting file to initiate the installation process on the Primary server. The Setup

Introduction dialog appears. Review the information and click OK.

10 The Self-Extractor dialog appears. Click Setup to continue.

11 The Setup Type page appears. Because this is a new installation of vCenter Server Heartbeat, select Install

vCenter Server Heartbeat and click Next.

12 Select the physical identity of the server on the Physical Hardware Identity page. Select Primary as the

server identity and click Next.

13 Read the license agreement carefully and select I accept terms of the License Agreement. Click Next.

14 Click Add to enter a valid serial number for production mode or leave blank to install in the evaluation

mode and click Next.

15 Select LAN for the network topology and click Next.

16 The Secondary Server is Virtual option uses the VMware vCenter virtual machine cloning to create a clone

of the Primary server while the Secondary Server is Physical option uses the native vCenter Server

Heartbeat cloning process to create a clone of the physical server. Select the Secondary Server is Virtual

option and click Next.

17 Configure the installation paths. The default installation location is C:\Program Files\VMware\VMware

vCenter Server Heartbeat, but you can change it by manually typing a path to another install location.

Alternatively, click Browse to select a different location. Click Next.

18 Identify the network adapters (NICs) for use in the VMware Channel on the Channel Adapter

Identification page by selecting the VMware Channel NIC from the list. Click the adapter name to display

the selected NIC properties in the lower pane. You must select at least one NIC to proceed with the

installation.

If no NICs are available, click Open Network Connections to review the network configuration of your

machine and verify that you have the correct number of NICs installed. After selecting the appropriate

NIC, click Next.

19 The VMware Channel IP Configuration page prompts you to configure the VMware Channel(s) IP

network addresses. Click Add for each available VMware Channel connection. For the Primary server,

select from a drop-down menu that lists all local IP addresses. Type the reciprocal IP address on the

Secondary server into the IP Address On Secondary text box. You must specify all VMware Channel IP

addresses in subnets outside of the normal Principal (Public) IP addressing schema. Click OK. Repeat this

step for additional NICs.

OTE If you click Exit after Setup has started, you are prompted to save your settings. When you run

Setup.exe later, you will be asked if you want to use the previously saved configuration.

NOTE The left pane of each page in the setup wizard provides information about the setup process.

OTE The path of the VMware installation folder cannot contain Unicode characters. If vCenter Server

Heartbeat is installed in a folder that has a path containing Unicode characters, this causes the VMware

vCenter Server Heartbeat service will to fail to start. The path of the VMware installation folder can only

contain lower and upper case letters A to Z, digits from 0 to 9, and the following special characters: space

\ _ - ( ) . : Additionally, vCenter Server Heartbeat does not support file or folder names ending with a

period “.” or space “ “.

OTE Only one channel can be configured for each NIC. To configure more than one VMware Channel

you must identify more than one NIC. A disabled NIC does not appear in this list. Enable the NIC to

display it. If a NIC is disconnected, its IP addresses do not appear in the lower pane.

OTE If you receive a warning message that the other server in the pair cannot be contacted, disregard

and click No to continue.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Commentaires sur ces manuels

Pas de commentaire

VMware VCENTER SERVER 4.0 - GETTING STARTED UPDATE 1 Guide d'installation Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Serveurs VMware VCENTER SERVER 4.0 - GETTING STARTED UPDATE 1