VMware VCENTER APPLICATION DISCOVERY MANAGER 6.1 - REPOSITORY Manuel d'utilisateur Page 101
- Page / 220
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
OneCommand™ Manager Application P007997-01A Rev. B
8. Managing Adapters and Ports
FC/FCoE
101
Note: If the adapter or firmware does not support Volatile WWNs, the “Write
changes to volatile memory for temporary use” checkbox is disabled. This
type of change is supported locally and via TCP/IP connections. This
checkbox is disabled for remote in-band adapters regardless of adapter
models and firmware version.
8. Click OK. The New WWPN and new WWNN values are saved for Volatile or
Non-Volatile use. The new WWPN and WWNN appear in the Pending Changes
section in the WWN Management area of the Maintenance tab.
9. Reboot the system for the changes to take effect. The new WWPN and WWNN will
appear in the Pending Changes section of the Maintenance dialog box until the
system is rebooted. After rebooting, the changes are applied and appear in the
Current section of the Maintenance dialog box.
Note: For VMware ESXi 4.x: After changing the WWN of an adapter, you must
reboot the system before trying to access the adapter on that system. (Refer
to VMware’s documentation to learn how.)
Creating and Deleting FC/FCoE Virtual Ports
Creating Virtual Ports
The OneCommand Manager application can automatically generate the WWPN for the
virtual port based on the WWPN for the physical port or you can manually type the
WWPN. You cannot generate virtual ports on 1 Gb/s and 2 Gb/s adapters.
Note: Neither the OneCommand Manager application nor the hbacmd utility can be
used to create or delete virtual ports on any VMware ESX server. Whereas
VMware ESX server supports NPIV, only VMware management tools can be
used to create and delete virtual ports.
Note: In Linux, virtual ports do not persist across system reboots.
The NPIV driver parameter must be enabled before attempting to create a virtual port.
The driver parameter name varies slightly depending upon your operating system:
For Windows: enableNPIV. On the Storport Miniport system, the SLIMode
driver parameter must also be set to 0 or 3.
For Solaris: enable-npiv
For Linux 8.2: lpfc_enable_npiv
See “Configuring the FC/FCoE Adapter Driver” on page 107 for more information on
enabling driver parameters.
To create a virtual port:
1. Do one of the following:
From the View menu, select Group Adapters by Virtual Ports.
From the toolbar, click Group Adapters by Virtual Ports.
- OneCommand™ Manager 1
- Application 1
- Version 6.1 1
- User Manual 1
- Table of Contents 3
- Table of Contents 4
- List of Figures 10
- List of Figures 11
- List of Tables 13
- 1. Introduction 14
- Compatibility 15
- Known Issues 16
- Abbreviations 16
- In Windows 18
- In Linux 20
- For RHEL 5 and RHEL 6 type: 21
- In Solaris 22
- In VMware ESX Server 24
- --maintenancemode update 25
- Web Launch Interface 26
- Installation 27
- Solaris: 28
- Linux: 28
- Web Launch Interface Only 29
- /opt/ELXocm/wsuninstall 30
- Manager Application 31
- Launch Interface 32
- Element Definitions 34
- Menu Bar 35
- Toolbar Buttons 35
- Discovery-Tree 37
- Property Tabs 38
- Status Bar 39
- Management Host 40
- 2. Run the following script: 41
- 5. Configuring Discovery 42
- Hosts File 43
- Adding a Single Host 45
- Adding a Range of Hosts 46
- Removing Hosts 48
- Adding Target Portals 52
- Removing a Target Portal 52
- Figure 5-7 iSCSI SNS Tab 53
- Logging into Targets 54
- Removing Targets 55
- Viewing Target Sessions 56
- Session Statistics Area 58
- Connection Information Area 59
- 7. Managing Hosts 61
- Function Summary Area 62
- Grouping Hosts 64
- Managing Host Groups 65
- Creating a Host Group 66
- Deleting a Host Group 66
- Adding a Host to a Host Group 67
- Restoring a Host Group 67
- Restoring all Host Groups 67
- Searching for Hosts 68
- Using CIM 69
- Viewing FC Port Information 71
- Viewing FCoE Port Information 73
- Figure 8-4 Statistics Tab 76
- Firmware Area 83
- WWN Management Area 84
- Mapping Information Area 87
- /usr/sbin/lpfc/lun_scan all 88
- LUN CapacityArea 89
- LUN Masking Area 89
- Current Settings Area 90
- Current Mappings Area 90
- Display Mode Radio Buttons 90
- Target Mapping Buttons 92
- Figure 8-14 LUN Masking Tab 93
- Changing Automapping Settings 95
- Adding a Persistent Binding 95
- Figure 8-18 Maintenance Tab 99
- Creating Virtual Ports 101
- 5x:xx:xx:xx:xx:xx:xx:xx 102
- 10:00:xx:xx:xx:xx:xx:xx 102
- 2x:xx:xx:xx:xx:xx:xx:xx 102
- 3x:xx:xx:xx:xx:xx:xx:xx 102
- Deleting Virtual Ports 103
- Figure 8-22 Virtual Port Tab 104
- Figure 8-24 Reset Warning 107
- Activation Requirements 108
- Setting Driver Parameters 110
- Resetting All Default Values 112
- Parameter Value 112
- DCB Settings Area 118
- CIN Settings Area 119
- DCB Tab Field Definitions 120
- Viewing iSCSI VPD Information 126
- Viewing iSCSI Statistics 127
- Viewing iSCSI LUN Information 131
- Viewing iSCSI PCI Registers 133
- DCBX Settings Area 136
- LLDP Settings Area 137
- PFC Priorities Area 137
- ETS Priority Groups Area 137
- Advanced TCP/IP Configuration 140
- Initiator Login Options Area 142
- Authentication Area 142
- Viewing NIC Port Information 144
- Viewing NIC VPD Information 146
- VPD Table Definitions 147
- Base Host Operating System 153
- Guest Host Information Area 154
- Operating System 155
- OneConnect Adapters 156
- Viewing ASIC Information 158
- Personality Area 160
- License Features Area 160
- Showing Licenses 162
- Installing Licenses 163
- Boot Code Versions Area 166
- PHY Data Field Definitions 169
- Error Rates Area 170
- Counters Area 170
- Module Attributes Area 171
- Diagnostic Data Area 172
- Linux Considerations 173
- Enabling Authentication 173
- DHCHAP Tab 175
- Changing Your Password 177
- 10. Updating Adapter Firmware 178
- Boot Types 183
- Boot Device Parameters 184
- 100 ms 191
- 200 ms 191
- 12. Exporting SAN Information 193
- 13. Diagnostics 194
- Information 195
- Viewing Flash Contents 195
- Viewing Overlay Details 196
- Viewing the PCI Registers 196
- Running a Quick Test 196
- Using Beaconing 197
- Creating Diagnostic Dumps 198
- LightPulse FC HBA Diagnostics 199
- Running Loopback Tests 200
- Loopback Test Combinations 201
- Saving the Log File 203
- OneConnect Diagnostics 204
- FCoE End to End Echo Test 206
- Error Action 206
- Test Cycles 206
- Test Pattern 206
- Test Status 206
- 14. Troubleshooting 211
- Situation Resolution 212
- Application Situations 214
- ./stop_ocmanager 215
- Situations 219
Produits connexes et manuels pour Logiciel VMware VCENTER APPLICATION DISCOVERY MANAGER 6.1 - REPOSITORY
(46 pages)Troy-Bilt 20” Rotary Mower — Model Series 100 manuali
Manuali dei proprietari e guide per l'utente per Apparecchi da giardinaggio Troy-Bilt 20” Rotary Mower — Model Series 100.
We fornisce 1 manuali pdf Troy-Bilt 20” Rotary Mower — Model Series 100 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commentaires sur ces manuels